2.4 intake idea?

[GTPprix]

Re: 2.4 intake idea?

Yea I probably did. Considering that I'm 18 they probably took advantage and I hear stories about it all the time. It's not like I can go back and demand my money back since tunes are no refund, but I can give that place a bad rep. I wish I had gotten the WAMS tune now, but that is later on my list.

What place was it so others dont get screwed?

[Abyssul]

Re: 2.4 intake idea?

Carolina Custom Shop in Conway, SC. Meh, learn from my mistakes

[tylerrice123]

Re: 2.4 intake idea?

so with the WAMS you can run a full cai setup on your car?

[shael]

Re: 2.4 intake idea?

so with the WAMS you can run a full cai setup on your car?

should be able to..

[Jacquel]

Re: 2.4 intake idea?

CAI on a 2.4.lt isn't gonna net you much. Just get a drop in high intake filter for the stock box, like the FRAM Air Hog. Also, if you really want to wake up the 2.4 do what I am doing, save an ass load of money and buy a Turbo or Supercharger then WAMS tune it.

[Phenom]

Re: 2.4 intake idea?

good luck w/ the s/c.... u gotta save about 4 grand.
turbo would be cheaper

[Pedobear]

Re: 2.4 intake idea?

good luck w/ the s/c.... u gotta save about 4 grand.
turbo would be cheaper

Depends on what/how you do it.

[Jacquel]

Re: 2.4 intake idea?

good luck w/ the s/c.... u gotta save about 4 grand.
turbo would be cheaper

Well I am looking more into the Turbocharger route, but ya gonna need to save either way it's gonna be 2.5grand min

[Phenom]

Re: 2.4 intake idea?

Parts List:
Eaton M62 Supercharger
Supercharger Gasket
Stock LSJ Intake Manifold
Intake Manifold Bottom Mount
Intake Manifold Gasket (Part #12597855)
2.5 Bar Map/Intake Temp Sensor (on upper left of LSJ manifold)
2.5 Bar Pigtail (Part #88988320)
Bosch/LSJ Intercooler Pump
Intercooler Pump Wiring Pigtail or Butt Connecters
Intercooler Pump Mounting Bracket (rebelautoworx.com)
Cobra Heat Exchanger (Used from a 03 Mustang Cobra)
Cobra Heat Exchanger Brackets (custom or bwoodyperformance.com)
42.5# Injectors (recommended)
Injector Harness
Wideband Air/Fuel Ratio Gauge (THIS IS NOT AN OPTIONAL ITEM!!!)
Boost/Vacuum Gauge
Stage 2 Belt (Part# 12597993; requires one rib be cut off)
Custom Idler Pulley with Mounting Bracket (rebelautoworx.com)
Extended Upper Radiator Hose
Coolant Reservoir Tank (Cobalt or Ion Recommend)
NGK Copper Spark Plugs (Part# LFR6A-11)
SS/SC intake
10ft. x ¾” I.D. Hose
10ft x ¼” I.D. Hose
4ft. x ½” I.D. Hose
Small and Large Hose clamps.
3 x 1/8th NPT ¼” Barb Fittings
Self Tapping Sheet Metal Screws (Mounting H/E brackets)
6M 25mm Bolts
6M 90mm Studs with Locking Nuts
8M 50mm Bolts
Water Wetter Coolant
1/8th NPT Drill Tap
21/64th Drill bit (for the 1/8th tap)
20 gauge wiring
Zip Ties
Electrical Tape
Plastic Wiring Sleeves


about 4K

[LoJac963]

Re: 2.4 intake idea?

^about the going rate for most 4-6 bangers, gets a little pricey when you jump up to the V8's though...

[Phenom]

Re: 2.4 intake idea?

i hope i get to experience the V8 aftermarket soon enough