If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Seen a couple mods in here that look pretty interesting to me! Like the side plates for sure, looks nice. And swapping to a canadian gauge, how hard is that cause that would be awesome and then mod to have white LED's like that, looks very classy i think.
The guage swap itself was very simple. There is a how-to floating around here somewhere about how to swap the LEDs.
Show: GXP Hood - 2009.5 Front Bumper & Rear Spoiler - Black Housing Headlights - White LED Reverse and License Plate Lights- White LED Interior Dome & Map Lights - Matsushita Gen4 6000K HID Lows - White LED Fogs - GXP Rear Bumper - White LED KPH Instrument Cluster Conversion - 15% Tint
Techno gray 07 G6 GT Sedan 20% tint, 6000K HID's, red LED floor lights, intake resonator removal, LED interior and reverse lights, debadged rear dart, gm emblem and pontiac emblem, and black emblem overlays.
The instrument cluster? It doesn't have the eyelids anymore. But here is an old pic I found.
Show: GXP Hood - 2009.5 Front Bumper & Rear Spoiler - Black Housing Headlights - White LED Reverse and License Plate Lights- White LED Interior Dome & Map Lights - Matsushita Gen4 6000K HID Lows - White LED Fogs - GXP Rear Bumper - White LED KPH Instrument Cluster Conversion - 15% Tint
Yeah the cluster. I haven't ever soldered (or needed to) anything
Techno gray 07 G6 GT Sedan 20% tint, 6000K HID's, red LED floor lights, intake resonator removal, LED interior and reverse lights, debadged rear dart, gm emblem and pontiac emblem, and black emblem overlays.
Yeah the cluster. I haven't ever soldered (or needed to) anything
Reading the how-to thread, it isn't something I would be interested in ever doing even though I want the white/red layout OP has. I've only ever soldered when fixing the broken battery holder on our keyfobs. I would suggest doing some reading, watching some videos, practicing on a scrap circuit board from some old electronics and then picking up an extra cluster from a junkyard and soldering that one. Then you just switch them out.
I may put some eyelids back on. But I've been thinking of getting some black housing headlights.
Show: GXP Hood - 2009.5 Front Bumper & Rear Spoiler - Black Housing Headlights - White LED Reverse and License Plate Lights- White LED Interior Dome & Map Lights - Matsushita Gen4 6000K HID Lows - White LED Fogs - GXP Rear Bumper - White LED KPH Instrument Cluster Conversion - 15% Tint
I may put some eyelids back on. But I've been thinking of getting some black housing headlights.
Get Eagle Eyes if you want a half way decent direct bolt on housing. If you get Spyders for any reason then get them retrofitted with a better projector because the projectors that are originally in them are garbage.
2009.5 Front Bumber, GXP Hodd and Black Housing Headlights
Show: GXP Hood - 2009.5 Front Bumper & Rear Spoiler - Black Housing Headlights - White LED Reverse and License Plate Lights- White LED Interior Dome & Map Lights - Matsushita Gen4 6000K HID Lows - White LED Fogs - GXP Rear Bumper - White LED KPH Instrument Cluster Conversion - 15% Tint
Show: GXP Hood - 2009.5 Front Bumper & Rear Spoiler - Black Housing Headlights - White LED Reverse and License Plate Lights- White LED Interior Dome & Map Lights - Matsushita Gen4 6000K HID Lows - White LED Fogs - GXP Rear Bumper - White LED KPH Instrument Cluster Conversion - 15% Tint
Comment