Tweet
Is it hard to install the ZZP Strut bar?
-
-
Re: ZZP Strut Bar
no2007 G6 2.4L VVT Ecotec- Black Sedan
Appearance: Tinted Tails, 15% Tint, Black Calipers, Black Overlays and Eyelids, Black Painted Upper Grills, Blacked out door trim, Flowmaster exhaust tip, G5 GT Wheels, Red Interior LEDs, Red LED Dome, removed front plate, added oem fogs
Performance: WAMS 93 ECU and TCM tune, Injen CAI, and Racingline STB
Future plans: Red LED Trunk Wiring, Black headlights, exhaust, black rims, eibach springs
-
Re: ZZP Strut Bar
if you can use a wrench you can do it...it's just removing the nuts on the strut towers, sliding the bar on, then putting the nuts back.
2007 G6 2.4L VVT Ecotec- Black Sedan
Appearance: Tinted Tails, 15% Tint, Black Calipers, Black Overlays and Eyelids, Black Painted Upper Grills, Blacked out door trim, Flowmaster exhaust tip, G5 GT Wheels, Red Interior LEDs, Red LED Dome, removed front plate, added oem fogs
Performance: WAMS 93 ECU and TCM tune, Injen CAI, and Racingline STB
Future plans: Red LED Trunk Wiring, Black headlights, exhaust, black rims, eibach springs
Comment
-
Re: ZZP Strut Bar
Originally posted by xxbrandonxx if you can use a wrench you can do it...it's just removing the nuts on the strut towers, sliding the bar on, then putting the nuts back.
just remember to put the nuts back on without stripping them out. check them in a couple hundred miles to make sure they haven't loosened.Comment
-
Re: ZZP Strut Bar
Is there a chance that it will rub the hood?Comment
-
Re: ZZP Strut Bar
yes.... Is that the tube one?
I think Barry had one that was rubbing.Please consider supporting G6P -Tap here
MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....
Comment
-
Re: ZZP Strut Bar
yes it will rub.
750WHP Magnacharged GTO.....WTF!
TVS2300 GTO, Innovators West 8" Overdrive Pulley, ECS Tensioner, SD tuned by Andrew at Complete street performance, Ed Curtis custom Lunati camshaft 230/236 .6XX/.6XX 113 LSA, Hardened Pushrods, Lunati .675 lift Valve Springs, Single Walbro 255 fuel pump in stock bucket, Kooks 1 7/8 Jet hot coated Headers , Kooks 3" catless mid pipes with DMH low pro electric cutouts, Spintech 2.5" stainless steel exhaust with X pipe, Carbon fiber Cold air box with AEM air filter, Billet products short shifter, JamesBiz Oil catch can, Pedders 5/16" raise springs with drag bags, Weld RTS Black with Hoosiers
Show
-20% tint
-bohaman AUX-in radio mod
-Professionally heated seatsComment
-
Re: ZZP Strut Bar
Is there one that doesn't?Comment
-
Re: ZZP Strut Bar
Mine doesnt rub. I used the tree method. I put it between two limbs and bent
each side outward about 1/4". There was enough play in the bolt pattern that it still clamps down with the bolt against the inside of the bolt hole now. You cant tell when the nuts are on it.
Funny thing..... I thought the GM Strut Bar was aluminum.
ITS NOT. I stripped the paint and it started rusting.
I just fixed that. I will show you pix tomorrow. Im at work till 9pm tonight.
Please consider supporting G6P -Tap here
MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....
Comment
-
Re: ZZP Strut Bar
PS...that ZZ company has such piss poor service I wouldnt buy
a thing from them. Just call them and see for yourself.
The owners name is Zap or some such crap.Please consider supporting G6P -Tap here
MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....
Comment
-
Re: ZZP Strut Bar
wait a few weeks for the taz bar...that's what im doing2007 G6 2.4L VVT Ecotec- Black Sedan
Appearance: Tinted Tails, 15% Tint, Black Calipers, Black Overlays and Eyelids, Black Painted Upper Grills, Blacked out door trim, Flowmaster exhaust tip, G5 GT Wheels, Red Interior LEDs, Red LED Dome, removed front plate, added oem fogs
Performance: WAMS 93 ECU and TCM tune, Injen CAI, and Racingline STB
Future plans: Red LED Trunk Wiring, Black headlights, exhaust, black rims, eibach springs
Comment
-
Re: ZZP Strut Bar
Taz's looks good....I think he fixed the clearance issue. Im just not sold on there being
bolts in play. I like the solid bar...but Im old school and it will prolly work just fine.
Is it still an option to have his bar engraved??Please consider supporting G6P -Tap here
MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....
Comment
-
Re: ZZP Strut Bar
No that was the MRZ bar I was working on and that one is dead in the water.Originally posted by LampoonDONE: debadged, cold air intake, Crimson Crab, red painted calipers and black painted rotors, painted engine and battery cover, eyelids, black emblem overlays, 235/55R16 tires, Raceingline engine mounts, Raceingline strut tower brace, Black recessed upper grilles.Comment
-
Re: ZZP Strut Bar
So how much will this Taz bar cost?Comment
-
Re: ZZP Strut Bar
Im picturing one with bolts.....is that the Taz one??? Or is it solid?Please consider supporting G6P -Tap here
MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....
Comment
Comment